500A Battery Monitor with Shunt + 40A DCDC Charger

Kings 40A DCDC Charger

Quick Connect Plugs | MPPT Solar Regulator Built In | Push Button Lithium Compatible | 12/24V Input | IP66 Rating

CHARGER, ISOLATOR + SOLAR REGULATOR

ALL IN ONE CHARGING SOLUTION

The Kings 40A DCDC Charger has a built in high-efficiency MPPT Solar Regulator that will track the maximum power point of a connected solar panel, so long as it has a minimum of 30W input. So you know you’re getting the most charge out of your panel no matter the conditions.

LITHIUM (LIFEPO4) CHARGING

WITH PUSH BUTTON BATTERY SELECTION

With a specially programmed charge pattern specific to 12V Lithium (LiFePO4) batteries, plus the ability to easily switch to standard 12V lead acid, AGM, Gel or Calcium batteries with the press of a button, the Adventure Kings DCDC will work with just about any setup - and is easy to adapt to your future setups too!

The Kings DC Charger also has an automatic lithium ‘wake’ feature where it will attempt to wake up or ‘jump start’ a lithium battery where the BMS has disconnected due to low voltage.

LITHIUM (LIFEPO4) CHARGING

WITH PUSH BUTTON BATTERY SELECTION

With a specially programmed charge pattern specific to 12V Lithium (LiFePO4) batteries, plus the ability to easily switch to standard 12V lead acid, AGM, Gel or Calcium batteries with the press of a button, the Adventure Kings DCDC will work with just about any setup - and is easy to adapt to your future setups too!

The Kings DC Charger also has an automatic lithium ‘wake’ feature where it will attempt to wake up or ‘jump start’ a lithium battery where the BMS has disconnected due to low voltage.

QUICK CONNECT PLUGS

ON INPUTS AND OUTPUT

Connecting your DCDC charger has never been easier - simply connect up the input from your starter battery, the output to your auxiliary battery and then connect a solar panel in seconds all thanks to the quick connect plugs. The 40A Charger along with a Kings 50A Wiring Kit is the perfect combo for an easy plug and play install!

BUILT IN MPPT SOLAR CONTROLLER/p>

WITH SOLAR PRIORITY CHARGING

The Kings 40A DCDC Charger has built in high-efficiency MPPT Solar Regulator that will track the maximum power point of a connected solar panel, so long as it has a minimum of 30W input. So you know you’re getting the most charge out of your panel no matter the conditions.

If, for example, you're driving at night and there is no solar input, the charger will pull only from your alternator.

When you stop at camp and turn off your vehicle, the DCDC will automatically swap over to solar charging.

If you're driving in the sun with both alternator and solar input, the DCDC will automatically prioritise solar input once it reaches the changeover threshold of 350W of solar power input.

BUILT IN MPPT SOLAR CONTROLLER

WITH SOLAR PRIORITY CHARGING

The Kings 40A DCDC Charger has built in high-efficiency MPPT Solar Regulator that will track the maximum power point of a connected solar panel, so long as it has a minimum of 30W input. So you know you’re getting the most charge out of your panel no matter the conditions.

If, for example, you're driving at night and there is no solar input, the charger will pull only from your alternator.

When you stop at camp and turn off your vehicle, the DCDC will automatically swap over to solar charging.

If you're driving in the sun with both alternator and solar input, the DCDC will automatically prioritise solar input once it reaches the changeover threshold of 350W of solar power input.

BUILT TOUGH FOR AUSSIE CONDITIONS

A tough alloy housing means it is able to survive harsh conditions, and continues to perform even in extreme temperatures. The Kings DCDC offers a 5-stage automatic current derating system that reduces power to protect the unit in extreme conditions. The internals are IP66 rated for excellent environmental protection thanks to the fully silicon potted circuit board.

The integrated heat sink for excellent passive cooling plus the Kings DC-DC is properly protected against reverse polarity, under or over voltage, as well as over temperature.

2 METRE TEMPERATURE SENSOR

PRECISE CHARGING IN ANY CONDITIONS

Adventure Kings DC-DC Chargers can output their stated 40 Amps of charge even in extremely hot ambient temperatures of up to 50°C and internal temperatures around 80°C. There’s an internal temperature sensor that monitors the circuit board and electronics to protect and regulate the output of the automatic 5-stage current derating - plus there's the 2m long temp sensor with ring terminal, designed to mount to your battery highly accurate charge compensation.

2 METRE TEMPERATURE SENSOR

PRECISE CHARGING IN ANY CONDITIONS

Adventure Kings DC-DC Chargers can output their stated 40 Amps of charge even in extremely hot ambient temperatures of up to 50°C and internal temperatures around 80°C. There’s an internal temperature sensor that monitors the circuit board and electronics to protect and regulate the output of the automatic 5-stage current derating - plus there's the 2m long temp sensor with ring terminal, designed to mount to your battery highly accurate charge compensation.

PLEASE NOTE

NOT for under bonnet installation

The item's colour may vary slightly between recent batches.

Dimensions

Kings 500A Battery Monitor With Shunt

Lithium Compatible | Backlit LCD Display | 500A Shunt | Temperature Sensor

BACKLIT LCD DISPLAY

CHECK YOUR BATTERY AT A GLANCE

The easy to read backlit LCD display makes it easy to check your battery status at a glance - and with just the press of a button you can check battery voltage, charging/discharging current, power, temperature or battery capacity percentage.

LITHIUM OR AGM COMPATIBLE

12V, 24V, 36V AND 48V SYSTEMS

The Adventure Kings Battery Monitor uses battery voltage readings, and a high precision 500A shunt to measure current and calculate Amp hours in and out - this means it can accurately display your battery’s capacity whether it’s AGM, Flooded Lead Acid or Lithium - and regardless of whether it’s 12V or 24V.

LITHIUM OR AGM COMPATIBLE

12V, 24V, 36V AND 48V SYSTEMS

The Adventure Kings Battery Monitor uses battery voltage readings, and a high precision 500A shunt to measure current and calculate Amp hours in and out - this means it can accurately display your battery’s capacity whether it’s AGM, Flooded Lead Acid or Lithium - and regardless of whether it’s 12V or 24V.

INCLUDED 500A SHUNT

IDEAL FOR INVERTERS

With the included 500 Amp shunt, the Kings Battery Monitor can measure the power draw of 12V accessories up to ~6000W - so it’s ideal for inverters. It not only gives you a real-time read out of the power being used, but also the Amp hours that you’ve taken out of your battery and the estimated time until discharged or recharged.

READS POWER IN AND OUT

The Shunt allows the Battery Monitor to calculate both power in and out - and if you’re charging your battery at the same time you’re using it, the Battery Monitor displays the total value! So if you’re charging 25A, but using 10A on 12V appliances, it will display 15A of charge!

READS POWER IN AND OUT

The Shunt allows the Battery Monitor to calculate both power in and out - and if you’re charging your battery at the same time you’re using it, the Battery Monitor displays the total value! So if you’re charging 25A, but using 10A on 12V appliances, it will display 15A of charge!

USER PROGRAMMABLE ALARMS

VOLTAGE, CURRENT AND TEMP

For extra monitoring, you can program over/under-voltage, over-current or over-temperature alarms - helping to keep an eye on your electrical system in any conditions. Plus, the included temperature sensor accurately monitors and allows the temperature of your battery to be displayed.